4 Secure the template to the mounting location. 5 Using a jigsaw or rotary tool, cut the mounting surface along the dashed line on the template. 6 Place the device in the cutout to test the fit. 7 If necessary, refine the size of the cutout. 8 After the device fits correctly in the cutout, verify the mounting holes on the device line up with the pilot holes on the template. 9 If the mounting holes on the device do not line up, mark the new pilot-hole locations. 12 If you will not have access to the back of the device after you mount it, connect all necessary cables to the device before placing it into the cutout. 13 Place the device into the cutout. 14 Secure the device to the mounting surface using the included M3 screws . 15 Install the decorative bezel by snapping it in place around the edges of the device. Stereo Information Specifications 10 Using a 1.5 mm (#53) drill bit, drill the pilot holes. 11 Remove the template from the mounting surface.
2 Using the included screws , secure the bracket to the top of the dock. The recommended torque you should apply to the screws is 5.0 to 6.0 lbf-in. (0.56 to 0.68 N-m). 3 Repeat this procedure for the side brackets . 4 Attach the clip-on nuts to the bottom edge of the dashboard, and attach the chassis bracket to the clip-on nuts using the included screws. 5 Attach the upper chassis bracket to the dashboard using the existing screws in the vehicle dashboard. 6 Attach the dock to the dashboard using the included screws. 7 Attach the included bezel to the front of the dock. 8 If necessary, install all remaining dashboard components. Installing the Device on a Wall The included template and hardware can be used to flush mount the device on the wall in your recreational vehicle. WARNING Always be sure of your mounting location before cutting into a wall. Recreational vehicle walls may contain utility lines. Failure to understand what is behind your mounting surface could result in damage to the vehicle, injury, or death. NOTICE Wall-mount kits are intended for wall-mount installations only. Do not attempt to install this device in a vehicle dashboard using a wall-mount kit. The wall-mount bracket includes the hardware required to attach the dock to a wooden surface. If you are mounting the device on a different material, you should use suitable hardware for your mounting surface. 1 Place each bracket on the dock , aligning the holes in the bracket with the holes on the dock.
Display Specifications Operating temperature range Charging temperature range
From -20 to 55°C (from -4 to 131°F)
From 0 to 45°C (from 32 to 113°F)
Wireless frequency/ protocol
2.4 GHz @ 15 dBm nominal
Power input
Vehicle power using the included vehicle power cable. AC power using an optional accessory (for home and office use only).
Battery type
Rechargeable lithium-ion
Dock Specifications Operating temperature range From -10 to 55°C (from 14 to 131°F) Storage temperature range From -20 to 70°C (from -4 to 158°F) Input voltage From 10.8 to 16 Vdc Current (max.) 15 A Current (standby mode) Less than 5 mA Fuse 15 A mini blade type Wireless frequency/protocol 2.4 GHz @ 7.9 dBm nominal
On-board, Class D Amplifier Output music power per channel Total output peak power Output power per channel
4 x 70 W max. 2 ohm
280 W max.
4 x 43 W RMS at 14.4 Vdc input, 2 ohm, 10% THD 1 4 x 26 W RMS at 14.4 Vdc input, 4 ohm, 10% THD 1
Line output level (max.) Aux. input level (typical)
5.5 V (peak to peak)
1 V RMS
2 Using the included M5 screws , secure each bracket to the dock. The recommended torque you should apply to the screws is 5.0 to 6.0 lbf-in. (0.56 to 0.68 N-m). 3 Trim the template, and confirm the device will fit in the location where you want to mount it.
1 The stereo may limit the output power to prevent the amplifier from overheating, and to maintain the audio dynamics. 5
Powered by FlippingBook