eBook-Sensor-System-ver-Feb2019

This interactive publication describes the best way to get maximum capacity life from an investment in Lithium Batteries in an RV, Caravan, Motorhome or 4WD. Covers the new CANbus technology and the breakthrough in cost reduction from a 48-12V Hybrid.

ENSORS CATALOG

SALES@SAFIERY.COM (07) 3040 9560 V20181011

SENSORS CATALOG

DOCUMENT AND CONCEPTS ARE COPYRIGHT SAFIERY PTY LTD

THE ITEMS THAT ARE COVERED IN A PACKAGE MAY VARY BECAUSE OF SENSOR AND/OR MODULE CONFIGURATION.

TEMPERATURE SENSORS STB01 BATTERY TEMPERATURE SENSOR

PRESSURE SENSOR SPH01 PRESSURE SENSOR SPR01 PRESSURE SENSOR-REFRIGERANT

21 22

4 5 6

STG01 WATERPROOF INTERNAL TEMPERATURE SENSOR STS01 WATERPROOF EXTERNAL TEMPERATURE SENSOR TANK LEVEL SENSORS STLU01 ULTRASONIC TANK LEVEL SENSOR IP68 STLPS01 SUBMERSIBLE TANK LEVEL SENSOR (Inside) IP68 STLPO01 TANK LEVEL SENSOR (Outside Fitting Bottom) IP67 STLC01 COMPACT TANK LEVEL SENSOR IP65 STLWXXX WEMA STYLE TANK LEVEL SENSOR N/A SOLAR PERFORMANCE SENSOR SSP01 SOLAR PERFORMANCE SENSOR

CABIN SENSOR SCP01 CABIN PRESSURE SENSOR SCD01 CABIN DUST SENSOR SCC01 CABIN CO2 SENSOR SCS01 CABIN SO2 SENSOR

24 25 26 27

10 11 12 13

LOAD SENSOR GVW01AXLE LOAD SENSOR

INCLINOMETER SENSOR SIN01 INCLINOMETER SENSOR AC CURRENT SENSOR SAC01 AC CURRENT SENSOR

TEMPERATURE SENSOR

4 STB01 BATTERY TEMPERATURE SENSOR Description Technical Specification

STB01 Temperature Sensor is Epoxy resin wrapped NTC sensor connected with insulated wire. It is waterproof with moisture protection, good insulation, high reliability, and sensitive response. The flat fixable probe is designed for monitoring the temperature of the battery. It works with Simarine Monitoring System and Smartphone App. Alerts can be sent if the temperature exceeds or drops below a preset level. The Temperature Sensor is especially critical for Lithium batteries in extreme climates.

Performance

Recommended application Battery Protection level Waterproof

Probe type Nickel plated copper flat fixable probe Probe size 9 x 10 mm, Inner diameter 4mm Length of wire 2 m Output 2 wires

Electrical Characteristic

Supply voltage 12V DC Measurement range - 20 – + 60 °C

Type NTC 10k ±1% 3950

B-constant

3380K ±1%

Typical Dissipation Constant 5mW/ °C Probe insulation >100MOhm Peak voltage sustain time 2 seconds, AC1800V 1mA 2 seconds Stress sustain 9.8N (1kgF) for 1 minute no deformation

5 STG01 WATERPROOF INTERNAL TEMPERATURE Description Technical Specification

STG01 Temperature Sensor is Epoxy resin wrapped NTC sensor connects with insulated wire. It is waterproof with stainless steel probe, moisture protection, good insulation, high reliability, and sensitive response. This temperature sensor is designed for monitoring the temperature of general devices, especially a fridge. To use with fridge, drill a 5mm hole from rear and insert the stainless steel probe with adhesive. It works with Simarine Monitoring System and Smartphone App. Alerts can be sent if the temperature exceeds or drops below a preset level. The Temperature Sensor is especially critical for boaters and RV relying on heating and cooling systems in extreme climates.

Performance

Recommended application Fridge Protection level

Waterproof Probe type Stainless steel probe Probe size 4.2 x 33 mm Length of wire 5 m Output 2 wires

Electrical Characteristic

Supply voltage 12V DC Measurement range - 20 – + 80 °C

Type NTC 10k ±1% 3950

B-constant

3380K ±1%

Typical Dissipation Constant 5mW/ °C Probe insulation >100MOhm Peak voltage sustain time 2 seconds, AC1800V 1mA 2 seconds Stress sustain 9.8N (1kgF) for 1 minute no deformation

6 STS01 WATERPROOF EXTERNAL TEMPERATURE Description Technical Specification

STS01 Temperature Sensor is Epoxy resin wrapped NTC sensor connects with insulated wire. It is waterproof with moisture protection, good insulation, high reliability, and sensitive response. The stainless steel braided sheath is durable and the sensor can work in the high temperature environment. This high quality sensor is designed for monitoring the temperature of the shock absorber. It works with Simarine Monitoring System and Smartphone App. Alerts can be sent if the temperature exceeds or drops below a preset level. The Temperature Sensor is especially critical for boaters and RV relying on heating and cooling systems in extreme climates.

Performance

Recommended application Shock Absorber Protection level

Waterproof & Heat resistant

Probe type Stainless steel probe Probe size 4 x 90 mm Length of wire 2 m stainless steel braided cable Output 2 wires

Electrical Characteristic

Supply voltage 12V DC Measurement range 0 – + 250 °C

Type NTC 50k ±1% 3950

B-constant

3380K -/+ 1%

Typical Dissipation Constant 5mW/ °C Probe insulation >100MOhm Peak voltage sustain time 2 seconds, AC1800V 1mA 2 seconds Stress sustain 9.8N (1kgF) for 1 minute no deformation

FLOW SENSORS

STF01 ULTRASONIC FLOW METER SENSOR

STFU01 Ultrasonic Flow Meter Level Sensor provides numerous advantages over other types of flow measuring meters: • 15mm Diameter Tube with BSP fittings • On board digital display (display output shown opposite) • Ultrasonic measurements are non-invasive. • Accurate flow measurement with a 400:1 turn down rate • Exceptionally reliable, doesn’t suffer any mechanical wear and tear. • Don’t cause the pressure to drop • Good for bidirectional measurements.

Performance Recommended application Any Liquid

Measurement mode Non-contact

Head Loss 0.25bar@Q3

Size (LxWxH)

165x85x80 mm

Overload Max Flow(Q4) Permanent Max Flow (Q3) Transitional Flow (Accuracy changes at this point) (Q2)

53.3 l/m 41.7 l/m

Q2 to Q4 +/-2% Q1 to Q2: +/-5%

Flow Accuracy

0.1667 l/m

Minimum Flow (Q1) 0.10417 l/m Liquid temperature Up to +50 °C

Max Working Pressure 16bar

Electrical Parameters

RS485 Proprietary Compatible Automate RV

• IP 68 this is fully submersible! • 12 Year battery operated life

Battery Operated 12 year target life

Communications

This flowmeter is an advanced and highly accurate ultrasonic water meter. With no moving parts, the robust design ensures reliable and long lasting precision. Its technology enables the measurement of even the lowest flow rates, making it the best solution for addressing smart water measurement.

TANK LEVEL SENSORS

10 STLU01 ULTRASONIC TANK LEVEL SENSOR Description Technical Specification

STLU01 Ultrasonic Tank Level Sensor with analog voltage output adopts the ultrasonic ranging principle THROUGH the measuring Liquid. It uses a special probe attached to the under-face (bottom) of the measured container to measure the level of the liquid level. It is suited to metal tanks. Special ultrasonic sensor using advanced high-speed signal processing technology is good for tanks up to 1.0m high. The assessed liquid level in the tank is calculated accurately by using the special algorithm. The measurement output is 0-5VDC signal. The design of this sensor suits RV manufacturers, The sensor has an LED on the underside. This is solid when 12V power is available. The sensor is placed by hand to the position where it will be adhered. The LED will flash to confirm the ultrasonic response is good and not fouled by baffles or pumps etc. When glued into position, excess glue is trapped in the glue recovery recess in the base of the unit. The material is anodized aluminium alloy of fine quality. The liquid level sensor has no special requirement on the material in the tank. Installation 1. The sensor needs to be placed in the centre at the bottom of the container. To make make sure there is no obstacle in the detection range there is an LED that “flashes” during installation. Bafles and other obstacles can therefore be avoided. Read on.. 2. Clean the detecting surface of the tank. If the metal tank has a paint coating, the surface of the detecting point has to be

Performance Recommended application Water Tank IP68

Measurement mode Non-contact

Length of wire 450mm

Size (LxWxH)

50x50x17 mm

Work temperature - 15 – +60 °C

Storage temperature - 25 – +80 °C

Electrical Parameters

Working voltage 10-36V DC

Average current

<25mA

Measuring height of liquid level Response time (without water)

Blind zone ≤50mm

50-1,000mm

Response time (with water)

Output mode Analog voltage

Resolution 1mm

Center frequency

2mHz

ESD ±4/±8KV

Accuracy (normal temperature)

±(10 + current height of liquid level*1%)

LED indicator light instructions Long bright

Power on, but did not detect the liquid Slow flash Liquid is detected and the LED flashes at one frequency per second

Electronic Wire Connections

Red VCC

Black GND

sanded until the metal is clean and polished. 3. If testing before final installation, press the sensor on the detecting point with ‘ coupling material’ (KY Jelly is best) for testing. When the LED is flashing, it confirms that it is good position for final installation. 4. Install the sensor permanently on the detecting point using a ‘ two part epoxy adhesive ’ 5. If the tank is poly-ethylene (roto-moulded tanks), it is advised to gently heat the area that you will be gluing to with a cigarette lighter to drive out any oils prior to gluing.

Yellow Signal Output +

White Reserved for later use

The Relational Graph Between Distance and approx voltage out.

11 STLCO01 COMPACT TANK LEVEL SENSOR (Fitted External Bottom) Description STLPO01 Pressure Sensor uses a high quality piezo-resistive pressure sensor (or flush ceramic sensor). It has an isolated stainless steel diaphragm as signal sensing element. Quality assembly procedures include: • Automatic testing, laser trimming compensated zero Technical Specification Parameter Pressure range 0-500mm Water Signal output 0-5V Power supply Overload 150%.F.S 1.5-2%.F.S

Measuring medium Fresh Water

12V DC

Burst pressure 200%F.S

Accuracy (Linearity hysteresis repeatability)

Stability 0.2%F.S ± 0.05%

• Special sensitivity in wider temperature range • Amplifier circuit is in stainless steel housing, • Transforming sensor signal into standard output signal.

Working Temperature -30°C~80°C

Storage temperature -40°C~85°C

Zero temperature drift

≤ 0.02%.F.S/°C/year

Net Weight

0.1kg

Piezo-resistive Flush Ceramic

Housing material

316 Stainless Steel

Diaphragm material

Insulate resistance >100MΩ @50V

Response time ≤10ms

Electronic Wire 3 Wires

Electronic connection Directly sealed cable IP67

Pressure connect port

G1/4” NPT male

Cable specs Water Proof

2m PE cable

Certificate approving CE Certificate

IP65

EMC Standard Electromagnetic radiation: EN50081-1/-2 Electromagnetic susceptibility: EN50082-2

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply +

Blue or Green Power Supply - Blue or Green Signal Output -

Blue or Green Ground Wire

Yellow Signal Output +

12 STLPS01 SUBMERSIBLE TANK LEVEL SENSOR Description STLPS01 Pressure Tank Level Sensor is a full sealed submersible level transducer/ transmitter. It is a highly stable and reliable piezo-resistive pressure sensor with an accurate circuit board in a stainless steel housing. It is an integrated construction with a standard control signal. The special cable is integrated with the housing and can be immersed into water for a long time. This sensor has compact size, light weight and good stability. It is rated as food grade. Parameter Measuring range 0-500mm, H2O Measuring medium Drinking Water Signal output 0-5V Power supply 12V DC Overload 150%.F.S Burst Pressure 300%F.S Accuracy (Linearity hysteresis repeatability) ≤ ± 1%.F.S Long Stability 0.2%F.S ± 0.05% Working Temperature -30°C~80°C Storage temperature -40°C~90°C Zero temperature drift ≤ 0.03%.F.S/°C/year Net Weight 0.1kg Housing material 304 Stainless Steel Diaphragm material Technical Specification

Piezo-resistive Flush Ceramic

Process material

304 Stainless Steel

Process material

304 Stainless Steel

Insulate resistance >100MΩ @50V

Response time ≤10ms

Electronic Wire 3 Wires

Electronic connection Directly sealed cable IP67

Pressure connect port

G1/4”

Cable specs Water Proof

1m PE cable

Certificate approving CE Certificate

IP68

EMC Standard Electromagnetic radiation: EN50081-1/-2 Electromagnetic susceptibility: EN50082-2

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply +

Black Power Supply -

Blue & Green Signal Output +

White/Yellow Signal Output -

Yellow Ground Wire

13 STLPO01 TANK LEVEL SENSOR (Fitted External Bottom) Description STLPO01 Pressure Sensor uses a high quality piezo-resistive pressure sensor (or flush ceramic sensor). It has an isolated stainless steel diaphragm as signal sensing element. Quality assembly procedures include: • Automatic testing, laser trimming compensated zero Technical Specification Parameter Pressure range 0-500mm Water Measuring medium Fresh Water Signal output 0-5V Power supply 12V DC Overload 150%.F.S Burst pressure 200%F.S Stability 0.2%F.S ± 0.05% 1.5-2%.F.S

Accuracy (Linearity hysteresis repeatability)

• Special sensitivity in wider temperature range • Amplifier circuit is in stainless steel housing, • Transforming sensor signal into standard output signal.

Working Temperature -30°C~80°C

Storage temperature -40°C~85°C

Zero temperature drift

≤ 0.02%.F.S/°C/year

Net Weight

0.1kg

Piezo-resistive Flush Ceramic

Housing material

316 Stainless Steel

Diaphragm material

Insulate resistance >100MΩ @50V

Response time ≤10ms

Electronic Wire 3 Wires

Electronic connection Directly sealed cable IP67

Pressure connect port

G1/4” NPT male

Cable specs Water Proof

2m PE cable

Certificate approving CE Certificate

IP67

EMC Standard Electromagnetic radiation: EN50081-1/-2 Electromagnetic susceptibility: EN50082-2

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply +

Blue or Green Power Supply - Blue or Green Signal Output -

Blue or Green Ground Wire

Yellow Signal Output +

14 STLWXXX WEMA STYLE TANK LEVEL SENSOR Description Technical Specification

STLW200, STLW400 & STLW450 WEMA Style Sensors for both fuel and water provides highly accurate level measurement for a wide variety of applications, including those in severe environments. Measurement is done using “hall effect” with reed switches positioned inside the level tube. A float with built-in magnets then triggers the reed relays generating a potential - free resistance with an ohm value that increases or decreases. The float is the only moving part of the sensors, thereby minimising potential mechanical failures. All sensors are fully insulated to protect against voltage inside the tank. The level sensors are made of stainless steel and can be mounted in almost any tank shape either by standard 5-hole configuration.

Parameter

200mm, 400mm, 450mm 240-33 Ω

Sensor Size

Measuring medium Fuel,Oil, Water

Signal output

Resolution 21mm

Working Temperature -40°C~85°C

Response time 0.1s

316 Stainless Steel OR 304 Stainlless Steel

Housing material

Mounting method Standard SAE 5 hold pattern

Protection Rank

IP67

Cable specs

50cm PVC cable

Dimension and Drawing (mm)

Instructions

To test correct operation, unscrew fuel sender, connect two wires to multimeter, set to resistance and move float up and down by hand. With float at the bottom it should read 0 ohm and at the top 180 ohm.

15 SLPG01 ULTRASONIC LPG TANK LEVEL SENSOR Description Technical Specification

SLPG01 Ultrasonic LPG Tank Level Sensor with analog voltage output adopts the acoustic reflection principle of the LPG tank level through a special conductive elastomer couplant to the metal LPG tank. It uses a circular rare earth magnet to attach to the under-face (bottom) of the LPG tank. Fitted between the Acoustic sensor and the tank is the special conductive elastomer couplant material. Inside the ultrasonic housing is a calibrated thermistor. The system sensor uses special ultrasonic processing technology. The echo signals are detected by the probe after being reflected back from the liquid surface. The echo signal is processed by the proprietary algorithm and the time is calculated. The system calculates the level of LPG according to the formula. There is no special requirement on the tank size. Installation 1. The sensor needs to be placed in the centre at the bottom of the LPG Tank. Please make sure there is no loose paint or debris at this point. 2. Clean the bottom surface of the LPG tank. If the metal tank has a thick or over- painted coating, the surface of the detecting point has to be clean and polished. 3. Place the couplant pad between the sensor and bottom of the tank. 4. Fit the alloy housing and magnetic ring to bottom of LPG tank. This is a strong connection which compresses the couplant material. 5. Check that the LED is flashing, as this confirms that it is good connection.

Performance Recommended application Water Tank IP68

Measurement mode Non-contact

Length of wire 2000mm

Size (LxWxH)

50x50x20 mm

Work temperature - 15 – +60 °C

Storage temperature - 25 +80 °C

Electrical Parameters

Working voltage 10-36V DC

Average current

<25mA

Blind zone ≤50mm

Measuring height of LPG level Accuracy (normal temperature)

50-1,000mm

Response time (with water)

± 4%

Output mode Analog voltage

Resolution 1mm

Center frequency

2mHz

ESD ±4/±8KV

LED indicator light instructions

Slow flash LED flashes every second for valid couplant engagement

Electronic Wire Connections

Red 12V power to sensor Yellow Signal Output

Black GND signal output/temp White Temperature

COUPLANT

CIRCULAR MAGNETIC MATERIAL

TEMPERATURE SENSOR

ULTRA SONIC DEVICE (AE)

SOLAR PERFORMANCE SENSOR

17 SPP01 SOLAR PERFORMANCE SENSOR Description SPP01 Solar Performance Sensor is measures solar irradiation to calculate the “solar intensity”. Place the sensing face upwards and flat on the same surface as the solar panels. The sensor detects solar irradiation on the incident to the installed plane. If shade is added, it can test the scattered radiation. It is widely used to monitor the solar irradiation in meteorology and solar energy. The Solar Performance Sensor has a range of 0-1500W/m2 and a cable 1500mm long for easy termination. Parameter Spectral range 300-3000nm Signal output 0-5V Sensitivity 7-14μv*w-1*m² Ingress Protection IP65 Working Temperature -40°C~85°C Storage Condition 10°C~60°C @ 20%-90% RH Technical Specification

Measure range 0-1500W/m²

Power supply

12V DC

Non-linear

<3%S

Stability ≤0.2%/year

Temperature effect

± 0.08%/°C

Cosine correction <10% (solar eleva- tion angle =10°)

Shell material

Aluminum alloy

Response time ≤5ms Cable length 1500mm

Sensor Net Weight

420g

Dimension and Drawing (mm)

Mounting

AC CURRENT SENSOR

19 SAC01 AC CURRENT SENSOR Description SAC01 AC Current Sensor provides a calibrated DC output proportional to the AC current input. It is set on a range of 0-30A input AC current. With this sensor, you will see the amount of shore or site power coming in. When set with low alarm, it will signal if you lose AC power input for whatever reason. Designed for multi-point current sensing, it uses classic current isolation and measurement systems. Performance Size (LxWxH) DIN rail

Technical Specification

95×37×88.5 mm 35mm Panel mount

Weight

120g

Aperture Size 20mm

Electrical Parameters Standard application IEC688:1992

Input range 0 - 30A

-10 ~ 50°C,20% -90%,non condensing Storage environment

-40 ~ 70°C,20% -95%,non condensing

Working environment

This device provide excellent ability for anti interference with accuracy of 0.5%. Average RMS is used when sensing current waveforms that have a fixed frequency.

Basic accuracy ≤0.5%.F.S

Calibration RMS calibrated Average sensing Output load 0-5V dc – 2k Ohm

Thermal drift

≤100PPM/°C (0~50°C)

Power consumption ≤30mA+output current

Power source 12V

Isolation voltage ≥100MΩ(DC500V)

Response time

≤300mS

Dimension and Drawing (mm)

Wiring Diagram

20 SAC01 AC CURRENT SENSOR Instruction of Installation and Use

Caution: 1. Pay attention to the auxiliary power information, especially the auxiliary power grade, and polarity, other wise will damage the product. 2. Pay attention to the wire connection; wrong terminal connection will cause malfunction of the product and even damage the product; 3. Don’t dismantle the product, and carry with care to avoiding bump and fall of the product; 4. If the product has been using under the environment with strong magnetic field interference, please pay attention to the shield of input wire, and the output signal wire should be as short as possible. For product intensive installation, the space between each product should not be smaller than 10mm. 5. Only use identified terminals. 6. There is no lightening strike prevention circuit design in this product. For out door and hazardous environment using, please add protective alternatives. 7. This product uses fire prevent ABS crust, its temperature withstand is only limited as +85°C, higher than this limitation will cause the product deformation. Please use and store carefully.

1. The product has compliance with EN50022; suitable for DIN rail mounting NS35/7.5, NS35/15. Installation steps are as following (please reference to dimensional drawing): Step 1: Immobilize one side of product‘s mounting trough to the DIN mounting rail; Step 2: Pull out the spring clasp; Step 3: Place whole mounting trough to the DIN mounting rail properly; Step 4: Release spring clasp to make sure the installation. 2. The product has calibrated before out of factory. After correctly wiring, it can be powered and used immediately. But for further precise signal sampling, user needs to warm-up the product for 3 minutes before use. a) The auxiliary power requires isolation voltage≥2000VAC, DC current output ripple <10mV, and multiple converters can share with one set auxiliary power together. b) Output signal (hz) is designed to follow the impedance load value of 250Ω; When Resistance (R1 ) is less than 100Ω, the user must add output current circuit a power reduced resistance load R0 to keep the summation of total impedance value is between 100Ω~ 250Ω.

3. The Maximum volume of line for the transducer terminal is 2.5mm 2 ; the insulation layer of the line should be peeled off about 8mm~10mm and tightly twisted to connect with the transducer terminals. 4. For the less than 10A AC current measurement, it may adopt ampere-turn method for input and for this time, the resolution of the transducer increases and measuring range narrows, but other technical index may not be affected.

INCLINOMETER SENSOR

22 SIN01 INCLINOMETER SENSOR Description SIN01 Inclinometer Sensor is a compact dual-axis inclinometer. Adopting the latest technology, with precision engineering from MEMS, this product has low power Consumption. It has excellent consistency and stability. It’s working temperature is -40 °C ~85 °C. A non-contact measurement principle is adopted to simultaneously output the pitch and roll inclination angles. Electrical Characteristic Performance

Technical Specification

Power supply (Unregulated voltage) Operating current (Non-loaded)

9 – 35 V (Typical 12V) 20 - 60 mA (Typical 50mA)

Operating temperature - 40 – +85 °C Sore temperature - 55 – +100 °C

Size (LxWxH)

91×40×26mm

Weight

150g

It can be easily operated and installed without knowing the exact “flat plane”. It has the latest MEMS sensor production technique which is characterized by high accuracy, small size, strong anti-electro-magnetic interference capacity, and great shockproof property. This product is perfect for vehicles and caravans.

Measuring range ± 30°

Measuring axis

X-Y

Zero point output

2.5(5) V

Zero temperature drift (-40°C-85°C)

± 0.01°/°C

Full scale output voltage 0-5V

Sensitivity error (25°C)

± 1%

Frequency response (DC)

100Hz

Output noise density (DC 100Hz)

0.0025

Resolution 0.02°

Accuracy 0.2°

Shock resistance 2000g,0.5m,- 3times/axis

Crossed sensitivity

Max 3%

Electrical Interfaces

Red V In

Grey & Black GND on both

Brown X Out

Orange Y Out

Mechanical Properties Connector

Direct lead (1.5m)

Protection level

IP67

Magnesium Aluminum

Shell material

Installation Four M4 screws

23 SI01 INCLINOMETER SENSOR Installation

Keep the sensor installation surface parallel to the measured objective plane during installation. Reduce the impact of motion and acceleration on the sensor. The product can be installed only horizontally.

PRESSURE SENSOR

25 SPH01 COMPRESSED AIR PRESSURE SENSOR Description Technical Specification

SPH01 Pressure Sensor will measure compressed air, fuel pressure, oil pressure, hydraulic pressure and gas pressure easily. It uses flush ceramic piezo-resistive Technology. The advanced circuit design minimizes the impact of temperature and Humidity. Its pressure chamber is made of 316L stainless steel welted with O-rings to give trouble free leakage. Digital circuits capable of strong RFI & EMI resistance and automatic temperature compensation are installed inside the transmitter and the transmitter is featured with strong interference resistance.

Parameter

Pressure range 0-300psi, Gauge

Measuring medium Compressed air

Signal output

0-5V

Power supply

12V DC

Overload 150%.F.S

Burst pressure 200%F.S

Accuracy (Linearity hysteresis repeatability)

≤ ± 0.5%.F.S

Stability 0.2%F.S ± 0.05%

Working Temperature -30°C~80°C

Storage temperature -40°C~85°C

Zero temperature drift

≤ 0.02%.F.S/°C/year

Net Weight

0.1kg

Piezo-resistive Flush Ceramic

Housing material

304 Stainless Steel

Diaphragm material

Process material

304 Stainless Steel

Medium compatible 304 Stainless Steel

Insulate resistance >100MΩ @50V

Response time ≤10ms

Electronic Wire 3 Wires

Electronic connection Directly sealed cable IP67

Pressure connect port

G1/4”

Cable specs Water Proof

1m PE cable

Certificate approving CE Certificate

IP65

EMC Standard Electromagnetic radiation: EN50081-1/-2 Electromagnetic susceptibility: EN50082-2

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply +

Black Power Supply -

Blue & Green Signal Output +

White/Yellow Signal Output -

Yellow Ground Wire

26 SPR01 REFRIGERANT PRESSURE SENSOR Description Technical Specification

SPR01 Pressure Sensor will measure refrigerant Pressure, especially R134(a). It uses flush ceramic piezo-resistive Technology. The advanced circuit design minimizes the impact of temperature and Humidity. Its pressure chamber is made of 316L stainless steel welted with O-rings to give trouble free leakage. Digital circuits capable of strong RFI & EMI resistance and automatic temperature compensation are installed inside the transmitter and the transmitter is featured with strong interference resistance.

Parameter

Pressure range 0-300psi, Gauge

Measuring medium Refrigerant

Signal output

0-5V

Power supply

12V DC

Overload 200%.F.S

Burst pressure 300%F.S

Accuracy (Linearity hysteresis repeatability)

≤ ± 0.5%.F.S

Stability 0.2%F.S ± 0.05%

Working Temperature -40°C~85°C

Storage temperature -40°C~100°C

Zero temperature drift

≤ 0.02%.F.S/°C/year

Net Weight

0.1kg

Piezo-resistive Flush Ceramic

Housing material

304 Stainless Steel

Diaphragm material

Process material

304 Stainless Steel

Medium compatible 304 Stainless Steel

Insulate resistance >100MΩ @50V

Response time ≤10ms

Electronic Wire 3 Wires

Electronic connection Packard 3 Pin Connector

Pressure connect port

G1/4”

Cable specs Water Proof

1m PE cable

Certificate approving CE Certificate

IP67

EMC Standard Electromagnetic radiation: EN50081-1/-2 Electromagnetic susceptibility: EN50082-2

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply +

Black Power Supply -

Blue & Green Signal Output +

White/Yellow Signal Output -

Yellow Ground Wire

CABIN SENSORS

28 SCP01 CABIN PRESSURE SENSOR Description Technical Specification

SCP01 cabin pressure sensor made to be highly accurate with a high stability, pressure sensitive Micro-chip. It has strict precise temperature compensation, linear compensation, signal amplification, V/I conversion, reverse polarity protection, current limiting pressure overload signal Processing. It will operate with very small pressure, flow and other parameters. The transducer is especially suited to measuring cabin pressure in the range of 0-100Pa.

Parameter

Pressure range 0-200pa, Gauge

Measuring medium air

Signal output

0-5V

Power supply

12V DC

Overload 200%.F.S

Burst Pressure 300%F.S

Accuracy (Linearity hysteresis repeatability)

≤ ± 0.5%.F.S

Long stability

0.2%F.S ± 0.05%

Working Temperature -30°C~80°C

Storage temperature -40°C~85°C

Zero temperature drift

0.03%.F.S/°C

FS temperature drift Pressure connect port

0.03%.F.S/°C

Housing material

Alloy

Open

Insulate resistance >100MΩ @100V

Response time ≤4ms

Electronic Wire 3 Wires

Electronic connection Directly cable IP65

IP65 (except air inputs)

Water Proof

Cable specs

1m PE cable

Certificate approving CE Certificate

Water Proof

IP65

Dimension and Drawing (mm)

Electronic Wire Connections

Red Power Supply + Yellow Signal Output + Black Ground & Shield Wire

Green Power Supply - Green Signal Output -

29 SCD01 CABIN DUST SENSOR Description SCD01 cabin dust sensor uses laser scattering principle, detecting the existence of dust particle concentration in the Air. The minimum can detect 1.0 um particles with good consistency and stability. Please specify if the range is PM1 or PM2.5 or PM10. Parameter Object Output

Technical Specification

PM1.0, PM2.5, PM10

Range 0-1000ug/m 3

0-5V

Power supply

12V DC

Accuracy ± 3%.F.S@25°C

Power consumption <50mA

Warm up time 3min

Response time <90s

Working Temperature -20°C~50°C @15%-80%RH

Storage temperature -40°C~60°C @20%-90%RH

Temperature drift

≤ 0.2%.F.S/°C

Stability < ± 2%.F.S

Repeatability

<± 1%.F.S

Shell material

ABS

Dimension and Drawing (mm)

30 SCC01 CABIN CO 2

SENSOR

Description SCC01cabin CO 2

Technical Specification

sensor uses NDIR principle to detect the CO 2

concentration in the

Parameter

Air. SPECIFY THE RANGE REQUIRED. It is designed with advanced infrared absorption gas detection technology, using a precise optical path and an excellent circuit. A temperature sensor is built-in for temperature compensation to ensure the accuracy of measurement. It is without oxygen dependence, and promises a long service life.

Range 0-2,000ppm; 0-5,000ppm; 0-10,000ppm Output 0-5V

Power supply

12V DC

Accuracy ± 3%.F.S@25°C

Power consumption Max:200mA, Avg:84mA

Warm up time 3min

Response time <90s

Working Temperature -20°C~60°C @15%-80%RH

Storage temperature -40°C~70°C @20%-90%RH

Temperature drift

≤ 0.2%.F.S/°C

Stability < ± 2%.F.S

Repeatability

<± 1%.F.S

Shell material

ABS

Dimension and Drawing (mm)

31 SCS01 CABIN SO 2

SENSOR

Description SCS01cabin SO 2

Technical Specification

sensor uses the specialized Sulfur dioxide sensor probe as core detecting device, which has the characteristics of wide measurement range, high precision, good linearity, good versatility, convenient using, easy installation, long transmission distance.

Parameter

Range 00-20ppm Output 0-5V

Power supply

12-24V DC

≤1.5W(@12V DC , 25°C)

Accuracy ≤±3%(25°C)

Power

Voltage output load ≤250Ω

Response time <15s

Working Temperature --30-50°C

HUMIDITY 0-100%RH(15- 95%RH)

Resolution 100ppb

Shell material

ABS

Dimension and Drawing (mm)

105mm

Electronic Wire Connections

Brown Power Supply +

Black Power Supply - Blue Signal Output -

Yellow/ Grey

Signal Output +

LOAD SENSORS

33 GVW01 AXLE LOAD SENSOR Description GVW Axle Load sensor will measure accurately the distance between the chassis and the axle. It uses infra-red and laser alignment sensor Technology. The advanced circuit design minimizes the impact of temperature and Humidity. Signal output

Technical Specification

Parameter Measurement Range 60-600mm

Measuring medium Air to metal target

0-5V

Power supply

10V-30V DC

Electrical Protection Short Circuit

Reverse Polarity

Protected

The application of this sensor to calculate the axle GVW is subject to a patent. Its sealed chamber is made of to give trouble free measurement. It requires the target

Repeat Accuracy

+/- 1%

Burst pressure 300%F.S

Temperature Influence ≤ ± 10% Working Temperature -25°C to 70°C

Stability 0.2%F.S ± 0.05%

area to be painted white for best performance. This may be an area only 50mm x 50mm is size.

Storage temperature -25°C to 80°C

Electronic Wire 3 Wires

Net Weight

0.1kg

Piezo-resistive Flush Ceramic

Digital circuits capable of strong RFI & EMI resistance and automatic temperature compensation are installed inside the transmitter and the transmitter is featured with strong interference resistance.

Housing material

Nickel Plated Brass

Sensing material

Insulate resistance >100MΩ @50V

Response time ≤30ms

18mm Diameter with SW24 lock nuts

Threaded Body

Cable specs

2m PE cable

Certificate approving CE Certificate European Standard EN60947-5-2 Dimension and Drawing (mm)

Water Proof

IP67

Electronic Wire Connections

Brown Power Supply +

Blue Power Supply -

Black Signal Output +

Blue Signal Output -

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34